Product ID:INTERSHIELD PRORECO 58, PRA050/A0/A0
MSDS Date:11/11/1996
FSC:8010
NIIN:00N083548
MSDS Number: CGQYD

COURTAULDS COATINGS INC

6001 ANTOINE DR
HOUSTON, TX 77091
US

Emergency Phone: 800-854-6813;800-424-9300(CHEMTREC)

Info Phone: 713-684-1563

Cage: 50411

INTERNATIONAL PAINT INC

HOUSTON, TX 77091 US

Telephone: 713-684-1244; 908-964-2206

Cage: 0TZA3

2-HEPTANONE; (HEPTAN-2-ONE)

CAS: 110-43-0

RTECS: MJ5075000

Fraction By Weight: 25-50%

OSHA PEL 100 PPM

ACGIH TLV: 50 PPM

BENZENE, 1,1'-METHYLENEBIS(ISOCYANATO-; (DIPHENYLMETHANE

CAS: 26447-40-5

Fraction By Weight: 10-25%

OSHA PEL N/K

ACGIH TLV: N/K

POLYMETHYLENEPOLYPHENYL ISOCYANATE;

CAS: 9016-87-9

RTECS: TR0350000

Fraction By Weight: 10-25%

OSHA PEL N/K

ACGIH TLV: N/K

POLYPROPYLENE GLYCOL

CAS: 25322-69-4

RTECS: TR5250000

Fraction By Weight: 10-25%

OSHA PEL N/K

ACGIH TLV: N/K

ISOCYANIC ACID, METHYLENEDI-P-PHENYLENE ESTER;

CAS: 101-68-8

RTECS: NQ9350000

Fraction By Weight: 1-10%

OSHA PEL C 0.02 PPM

ACGIH TLV: 0.005 PPM

EPA Report Quantity: 1 LB

DOT Report Quantity: 1 LB

ADIPIC ACID, POLYMER WITH 1,4-BUTANEDIOL, ETHYLENE GLYCOL

CAS: 27083-55-2

RTECS: AV2051000

Fraction By Weight: 1-10%

OSHA PEL N/K

ACGIH TLV: N/K

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: INHALATION: CAUSES NOSE AND
THROAT IRRITATION. EYES: CAUSES IRRITATION. SKIN: CAUSES
IRRITATION. CAN BE ABSORBED THRU SKIN. MAY CAUSE ORGAN DAMAGE. MAY
CAUSE ALLERGIC SKIN REACTION. INGESTION: MAY BE FATAL IF SWALLOWED
AND MAY CAUSEORGAN DAMAGE. CHRONIC: NONE SPECIFIED BY MANUFACTURER.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:IN ALL CASES OF DOUBT/WHEN SYMPS PERSIST, SEEK MED ATTN.
NEVER GIVE ANYTHING BY MOUTH TO AN UNCON PERS. INHAL: REMOVE TO
FRESH AIR. IF DISCOMFORT IS PRESENT/BRTHG IS ABSENT, GET MED ATTN
IMMED. EYES: FLUSH IMMED W/PLENTY OF WATER FOR AT LEAST 15 MIN
UNTIL IRRIT SUBSIDES. IF IRRIT PERSISTS, GET MED ATTN. SKIN: FLUSH
W/LGE AMTS OF WATER. USE SOAP IF AVAIL. REMOVE SEVERELY CONTAM
CLTHG (SUP DAT)

Flash Point:112F,44C
Lower Limits:1.11%
Extinguishing Media:FOAM, CARBON DIOXIDE, DRY CHEMICAL.
Fire Fighting Procedures:WEAR NIOSH APPROVED SCBA AND FULL PROTECTIVE
EQUIPMENT . IN ABSENCE OF ELECTRICITY, WATER SPRAY (FOG NOZZLE IS
PREFERRED) MAY BE USED TO COOL CONTAINERS.
Unusual Fire/Explosion Hazard:ISOLATE FROM HEAT, SPARKS, ELEC EQUIP &
OPEN FLAME. CLOSED CONTRS MAY EXPLODE WHEN EXPOSED TO EXTREME HEAT.
DECOMPOSITION & COMBUSTION PRODUCTS MAY BE TOXIC.

Spill Release Procedures:CONTAIN SPILLED LIQUID WITH SAND OR EARTH. DO
NOT USE COMBUSTIBLE MATERIALS SUCH AS SAWDUST. ABSORB SPILL WITH AN
INERT MATERIAL (E.G., DRY SAND OR EARTH), THEN PLACE IN A CHEMICAL
WASTE CONTAINER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:KEEP CONTAINER CLOSED. LOOSEN CLOSURE
CAUTIOUSLY BEFORE OPENING. STORE IN COOL, WELL-VENTILATED PLACE
AWAY FROM INCOMPATIBLE MATERIALS.
Other Precautions:KEEP AWAY FROM HEAT, SPARKS & FLAMES. PROTECT
MATERIAL FROM DIRECT SUNLIGHT. GROUND & BOND CONTRS WHEN
TRANSFERRING MATERIALS. EMPTY CONTRS MAY RETAIN HAZARDOUS
PROPERTIES. FOLLOW ALL MSDS/LABEL WARNI NGS, EVEN AFTER CONTAINER
IS EMPTIED.

Respiratory Protection:USE RESPIRATOR APPROVED BY NIOSH TO REMOVE
PARTICULATES (AND VAPORS IF THERE IS OVEREXPOSURE TO VAPORS
GENERATED DURING THE PROCESSING OF THIS PRODUCT).
Ventilation:PROVIDE SUFFICIENT VENT, IN VOL & PATTERN, TO: A) KEEP TLV
BELOW LIMS SPECIFIED. B) REMOVE VOLATILES PRODUCED (SUP DAT)
Protective Gloves:CHEMICAL RESISTANT GLOVES.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGLES .
Other Protective Equipment:ANSI APPROVED EMERGENCY EYEWASH & DELUGE
SHOWER . PROTECTIVE CLOTHING AS NEEDED TO AVOID CONTACT WITH
PRODUCT.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
FIRST AID PROC: (INCL SHOES) & WASH BEFORE REUSE. IF IRRIT PERSISTS,
GET MED ATTN. INGEST: DO NOT INDUCE VOMIT. KEEP AT REST. GET PROMPT
MED ATTN. VENT: DURING CURE & DECOMP PRODS PRODUCED DURING WELD
ING/CUTTING ON SURFACES COATED W/THIS PROD.

Boiling Pt:B.P. Text:300F,149C
Vapor Density:HVR/AIR
Spec Gravity:1.018
Evaporation Rate & Reference:SLOWER THAN ETHER
Appearance and Odor:LIQUID

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS FUMES WHEN
HEATED TO DECOMP AS IN WELDING. FUMES MAY PRODUCE CARBON DIOXIDE &
CARBON MONOXIDE.

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE AND
FEDERAL REGULATIONS. DO NOT INCINERATE UNOPENED CONTAINERS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.